PRECISIONYour partner for metal solutionsRequest a Quote

Machining processes

Types of CNC Machines: Which Processes and Parts Are They Used For?

Compare CNC lathes, machining centers, five-axis and turn-mill machines. Match part features to processes and prepare a clearer manufacturing enquiry.

Start with the part geometry, functional features and acceptance requirements, then assess the machine and process route.

01Match the machine to the features on your part

A threaded sleeve, a mounting plate and a contoured component may all be precision parts, but they do not necessarily suit the same machining route. Features around a central axis usually suggest turning; faces, pockets and hole patterns often suggest milling. Angled features and complex surfaces need a closer review of access, holding and machine configuration.

CNC describes computer numerical control, rather than one particular cutting process. The comparison below is a starting point for a manufacturing discussion. It is general equipment guidance, not an OY equipment inventory or a guarantee that every listed process is available. Machines within the same family differ in travel, tooling, control and workholding.

Scroll sideways to compare all columns.

Machine familyTypical operationsFeatures or parts to assessKey review points
CNC latheTurning diameters, faces, bores, grooves, tapers and threadsShafts, sleeves, pins and round fittingsDiameter, length, mating features and coaxial requirements
Three-axis machining centerFace, contour and pocket milling; drilling and tappingMounting plates, brackets, housings and blocksTool access, clamping and reorientation
Four-axis machining centerRotary positioning; coordinated rotary machining where equippedFeatures around a component or on several sidesIndexed positioning versus continuous motion
Five-axis machining centerAngled positioning; simultaneous contour machining where equippedAngled holes, multiple inclined faces and complex surfacesWhether positioning is sufficient or simultaneous motion is needed
Turn-mill machineCombined turning, milling and drillingRotational parts with flats, slots or cross-holesDriven tooling, axis configuration and feature access
Swiss-type CNC latheBar-fed turning with configured drilling and milling operationsSmall components, slender pins and connectorsBar specification, length-to-diameter ratio and guide-bush arrangement
CNC grinding machineSurface, external or internal grinding, depending on machine typeFaces, shafts and bores requiring a further finishing operationGrinding allowance, material condition and acceptance requirements

Technical reference: DMG MORI: Turn & Mill machines; Star CNC: Swiss-type automatic lathes; UNITED GRINDING: Grinding machine families

02Use turning to assess features around a central axis

In conventional turning, the workpiece rotates while the tool removes material. External diameters, internal bores, shoulders and grooves are common reasons to assess a lathe-based route. A sleeve with an outside locating diameter, a mating bore and an end thread is a useful example.

If that sleeve also needs a cross-hole or a flat, ask how the additional feature will be produced. It may require a separate milling or drilling operation, or suitable driven tooling on an appropriately configured machine. A lathe label alone does not establish those capabilities.

For quotation, identify which cylindrical features must align and which face locates the assembly. Describe the functional relationships rather than relying on the phrase high precision. The supplier can then review the proposed setup and inspection approach against the actual requirements.

Specify critical dimensions and feature relationships →

03Use machining centers for faces, pockets and hole patterns

In typical milling, the cutting tool rotates and the workpiece is located by workholding. An installation plate may require an outside profile, counterbores, tapped holes and locating slots. A three-axis machining center is often a sensible route to assess before considering more complex equipment.

A feature that exists in a CAD model is not automatically accessible to a practical cutting tool. Review the space inside a deep pocket, the permitted internal corner radius, support for a thin wall and the reference used after reorienting the part. These questions help distinguish a workable process from a machine-name comparison.

Part orientation also matters. Features on opposite sides may require another setup unless suitable access and workholding are available. Discuss how related features will be located and checked across those operations. Do not assume a single setup can expose every face of a component.

04Separate rotary positioning from simultaneous machining

An added rotary axis changes the orientation between the tool and workpiece. This can provide access to another face and may reduce repeated manual clamping. Four-axis equipment can be used for indexed positioning, or coordinated motion if the machine and control support it.

Haas distinguishes 3+2 positioning from simultaneous five-axis machining. The distinction is useful when explaining what a part needs: access to several fixed angles is a different task from continuously changing the tool orientation along a surface.

More axes do not automatically make every dimension more accurate or every quotation less expensive. Tooling, fixtures, programming, material behavior and measurement still determine the delivered result. Ask which feature requires the proposed configuration and how that choice affects the process.

Scroll sideways to compare all columns.

ApproachHow it is usedFeatures to assess
3+2 positioningTwo rotary axes establish an orientation; three-axis cutting follows at that orientationInclined faces, angled holes and several accessible sides
Simultaneous five-axis machiningLinear and rotary axes coordinate during cuttingSurfaces requiring continuously changing tool orientation

Technical reference: Haas: 3+2 positioning and simultaneous five-axis machining

05Compare complete process routes, not equipment labels

A shaft with a cross-hole and a controlled outside mating surface may be evaluated as turning followed by a separate hole operation, with further finishing if required. Another option is a suitably equipped turn-mill machine, followed by any necessary finishing.

DMG MORI describes turn-mill equipment that combines turning and milling within one work area. Whether that integration benefits a particular order depends on feature access, tooling, setup, quantity and the required relationships between surfaces. It should not be taken as proof that a combined route is always cheaper.

Use a simple route review: list each feature, its process, how it will be held and when it will be inspected. If the proposed route changes, confirm that the final drawing and surface requirements remain satisfied. A process plan should explain the delivered component, not merely advertise the most elaborate machine.

Review the effect of finishing on final dimensions →

Technical reference: DMG MORI: Turn & Mill machines

06Know when grinding or EDM needs a separate review

Grinding equipment includes different families for surface, external cylindrical and internal cylindrical work. If grinding is proposed after another operation, agree on the allowance, material condition and final acceptance characteristics. A generic CNC grinding description does not identify the correct machine or process.

For electrically conductive materials with features that are difficult to reach by conventional cutting, electrical discharge machining may be worth assessing. Wire EDM, sinker EDM and EDM hole drilling are different processes. They should not be treated as interchangeable options.

Wire access and the required geometry must be checked; wire cutting is not a general solution for an arbitrary enclosed blind cavity. The proposed process may also affect the surface and subsequent finishing requirements. Resolve these details with the manufacturing specialist before approving the route.

Technical reference: UNITED GRINDING: Grinding machine families; Makino: Electrical discharge machining

07Send the requirements that make equipment selection useful

Customers can specify equipment where the project requires it. Otherwise, a clear part requirement often gives the supplier more useful information than a machine name. Provide the following items and identify anything that is still undecided.

An early concept does not need a finished production drawing before discussion can begin. Explain the function, installation space and mating components, using a sketch or reference image where available. Those inputs help define the structure and manufacturing questions that need resolution.

OY Precision reviews custom metal part enquiries against the specific project requirements. Equipment arrangements, process availability and inspection scope need confirmation during review. This guide does not claim that OY owns or offers every machine family described.

  • Geometry and size: drawing, model or sketch where available.
  • Material grade and condition, or the operating requirements if not selected.
  • Critical holes, diameters, faces and mating relationships.
  • Dimensional and surface requirements, including the stage at which they apply.
  • Sample quantity and expected production quantities.
  • Inspection characteristics and required records.

Discuss a CNC machining project →

Start from an idea or sketch →

Technical references

Discuss your part requirements

Send the details you have. Drawings and file uploads are optional.