PRECISIONYour partner for metal solutionsRequest a Quote

Material selection

Precision Machining Materials: Brass, Copper, Stainless Steel and More

Compare brass, copper, stainless steel, aluminum, carbon steel, alloy steel and titanium by properties, machining requirements and typical part applications.

Compare brass, copper, stainless steel, aluminum, carbon steel, alloy steel and titanium before specifying a precision component.

01Choose for the part, then specify the material

Precision machining material selection starts with what the component must do: conduct heat, locate an assembly, resist an environment, carry load or provide a particular surface. Material names help narrow the discussion, but a family name alone does not define a deliverable part. Grade, condition, product form and the required features belong in the decision.

The seven families below are comparison categories, not interchangeable specifications or a guarantee that every grade can be supplied and machined. OY Precision reviews enquiries for precision components in multiple materials. Confirm the proposed material and manufacturing scope against the actual part before ordering.

02Compare material properties, applications and finished parts

Published reference values below apply to the stated grades, conditions and product forms. Typical values, ranges and limits are identified; the final part specification still needs the material grade, condition and acceptance requirements.

Compare representative grades and conditions, rather than assigning one value to an entire metal family.

On smaller screens, swipe the table sideways. The material column stays visible.

Material properties, applications and finished parts
Material / gradeDensityg/cm³Hardnessscale as statedTensile strengthMPaThermal conductivityW/(m·K)ApplicationsSelection notesFinished-part example
BrassC36000H02 half-hard rod[1]8.5065 HRB typ.393 typ.116Threaded fittings; bushingsCheck lead restrictions and the required finish.Threaded fitting
CopperC11000 ETPOS050 annealed flat product[2]8.9140 HRF typ.221 typ.391Heat spreaders; electrical contactsSpecify the copper grade, contact face and burr control.Copper heat spreader
Stainless steelSanmac 304/304LSolution-annealed bar[3]7.9≤215 HB515–68015Equipment fittings; flanged shaftsMatch the grade and surface finish to the environment.Flanged shaft
Aluminum6061-T6/T651Sheet / coil / plate[4]2.7095 HB typ.310 typ.167Electronics housings; bracketsInclude the temper and final surface requirements.Machined housing
Carbon steelC45 · 047A+QT round bar, 10 < d < 40 mm[5]7.80210–240 HB690–77040–45Locating pins; machine shaftsAgree heat treatment and corrosion protection.Shouldered locating pin
Alloy steel42CrMo4 · 1.7225Soft annealed[6]7.75≤217 HBW≈72045.1Gears; loaded shaftsFinal service hardness may need a different heat treatment.Spur gear
Titanium alloyTi-6Al-4V ELI · Grade 23Annealed CAD/CAM blanks[7]4.4280–330 HV10≥8606.6Weight-sensitive brackets; fittingsConfirm the specific grade and qualification requirements.Lightweight bracket

Reading the numbers: density compares weight for the same volume; tensile strength describes resistance to being pulled apart; thermal conductivity describes how readily heat passes through the material.

Key: typ. = published typical value; ≤ = maximum; ≥ = minimum. Conductivity is at 20°C except C45 (ambient). The sources below identify product sizes and test conditions. These are reference values, not OY test results or a supply guarantee.

Hardness: HB/HBW, HRB, HRC and HV are different test scales. Do not rank unlike scales by their raw numbers. Values belong to the stated condition and source, not every part made from that metal.

Finished-part images are AI-generated illustrations of possible component forms, not OY customer projects, material identification or proof of a specific grade.

Data conditions and sources
  1. C36000 — H02 half-hard rod. Typical mechanical values for H02 rod below 0.50 in (12.7 mm), tested at 20°C. Density and thermal conductivity are grade-level reference values at 20°C, not separately temper-qualified. UTS converted from 57 ksi; conductivity from 67 Btu/(h·ft·°F). This is a leaded free-cutting brass. Copper Development Association: C36000 alloy data
  2. C11000 ETP — OS050 annealed flat product. Typical mechanical values for OS050 annealed flat product, 0.025 in (0.635 mm) thick with nominal 0.050 mm grain size, at 20°C. Hardness is Rockwell F. Density and conductivity are grade-level values at 20°C. UTS converted from 32 ksi; conductivity from 226 Btu/(h·ft·°F). ETP is not oxygen-free copper. Copper Development Association: C11000 alloy data
  3. Sanmac 304/304L — Solution-annealed bar. Manufacturer delivery-condition bar data at 20°C: maximum hardness and tensile range. Thermal conductivity at 20°C; density temperature is not separately stated. The data describe Alleima Sanmac bar, not all 304/304L products. Alleima: Sanmac 304/304L bar datasheet
  4. 6061-T6/T651 — Sheet / coil / plate. Kaiser sheet/coil/plate datasheet: T6 and T651 share the typical mechanical-property row. Brinell hardness uses a 500 kg load and 10 mm ball. Nominal density and typical conductivity are at 20°C. Mechanical test temperature is not specified in that table. Kaiser: 6061 Sheet, Coil and Plate technical data
  5. C45 · 047A — +QT round bar, 10 < d < 40 mm. Ovako variant 047A, quenched and tempered (+QT) round bar, dimension 10 < 40 mm as tabulated: tensile and hardness ranges. Density and conductivity are grade-level typical physical properties; conductivity is at ambient temperature, not a separately identified +QT test. These are reference values for the stated manufacturer product. Ovako Steel Navigator: C45, revision 2025-01-30
  6. 42CrMo4 · 1.7225 — Soft annealed. Einsal manufacturer reference: soft-annealed condition, maximum 217 HBW and approximate tensile strength. Conductivity is at 20°C; mechanical test temperature and section size are not stated. Density follows the manufacturer value, rather than a generic steel value. Walzwerke Einsal: 1.7225 / 42CrMo4 material data
  7. Ti-6Al-4V ELI · Grade 23 — Annealed CAD/CAM blanks. Zapp Ergitan 3.7165 ELI annealed CAD/CAM blanks: hardness range and minimum tensile entry; conductivity at 20°C. Density and mechanical test temperatures are not separately specified. The datasheet is non-binding reference information. Grade 23 ELI is not Grade 5; no medical or aerospace supply approval is implied. Zapp: Ergitan 3.7165 ELI datasheet, July 2020

03Brass and copper need separate specifications

Brass is a copper-zinc alloy family. It is not another name for unalloyed copper. Kupferverband distinguishes machining brasses from other compositions and explains why chip behavior can differ among copper materials. A free-cutting brass specification should not be silently replaced with a different brass merely because both appear yellow.

Copper is commonly considered when heat or electricity must pass through a component. The International Copper Association identifies conductivity as one of its central attributes. Brass is a different selection: its zinc content and other additions change the balance of machining behavior and service properties. A threaded fitting and a heat-transfer contact should therefore not be assigned the same material merely because both are copper-based.

For copper, terms such as pure copper or red copper do not automatically identify a particular procurement grade. Specify the material designation and condition, or identify selection as an open question. A conductivity requirement, joining requirement or composition restriction needs its own basis. Appearance cannot verify any of these.

If lead content or another substance restriction matters, state the applicable purchasing requirement and requested documentation. Do not assume that a material called lead-free has been verified against the specific limit relevant to your product.

Prepare a custom copper heat sink enquiry →

Technical reference: Kupferverband: Copper-zinc alloys (brass); Kupferverband: Machining copper materials; International Copper Association: Copper attributes and alloys

04Stainless steel is not a single corrosion or machining specification

Outokumpu groups stainless steels by metallurgical type and documents differences in their properties. Select against the actual medium, temperature and service conditions rather than asking for a part that simply never rusts. Where an existing drawing specifies a grade, seek approval before substituting another.

Magnetic response is not a stainless authenticity test. Outokumpu identifies ferritic, martensitic and duplex grades as ferromagnetic, unlike stable austenitic grades. Verify the required material through agreed documentation or identification methods, not a magnet alone. Ask separately about machining, surface finish and any cleaning or treatment requirements.

Technical reference: Outokumpu: Stainless steel types and properties; Outokumpu: Machining guide

05For aluminum, include the temper and starting form

Hydro’s 6061 and 6063 extrusion datasheets attach properties to specified conditions. They should not be turned into one universal aluminum value. A part cut from plate and a part made from an extrusion require attention to their respective product specifications.

For a profile, identify the cross-section and the features added afterward. For a machined housing, identify the starting material and the finished interfaces. If visible surfaces need an agreed finish, specify that reference independently of the alloy name. Neither a grade number nor a photograph guarantees an exact appearance.

Compare 6061 and 6063 aluminum for parts and profiles →

Technical reference: Hydro: Alloy 6061 extrusion datasheet; Hydro: EN AW-6063 extruded products datasheet

06Include the final condition for steels and titanium

Carbon steel and alloy steel are broad engineering categories. Ovako’s guidance shows that quenching-and-tempering steels can be unalloyed or low-alloyed; a processing label therefore does not identify one composition. Record the actual grade, delivery condition and final requirements instead of choosing from family labels alone.

Ask which critical features are accepted after heat treatment, finishing or another agreed operation. If corrosion protection is required, define it as part of the delivered condition. Do not compare quotes for untreated stock and a finished, treated component as though their scopes were identical.

Titanium also needs a specific grade and condition. TIMET’s handbook separates material choices and gives dedicated machining guidance, including cooling considerations. Do not transfer cutting assumptions from aluminum or declare every titanium grade suitable for aerospace or medical use. Those applications need their own specifications and approval processes.

Technical reference: Ovako: General engineering and structural steel; Ovako: Quenching and tempering steel; TIMET: Titanium design and fabrication handbook

07Compare complete component proposals

Consider an illustrative spacer that must maintain an assembly gap. Before choosing between brass, stainless steel and aluminum, identify the loads, contact environment, allowed mass and critical interfaces. This is a selection exercise, not an OY case study. The designer must decide which requirements govern.

Compare proposals using the same grade basis, condition, geometry, finishing and inspection scope. Ask a supplier to identify any proposed substitution. A material that reduces one purchasing line may introduce other processing or acceptance work, so neither cheapest nor best can be assigned reliably to an entire family.

08Copy this material-selection note

Complete what you know and leave unresolved choices visible. This brief helps connect material selection to the delivered part rather than repeating a general drawing-upload checklist.

  • Component function and critical interfaces:
  • Operating loads, temperature, environment and contact materials:
  • Proposed material grade, governing specification and condition:
  • Starting product form and relevant dimensional range:
  • Required final heat treatment, finish or protective treatment:
  • Composition restrictions and material documentation required:
  • Features and inspection requirements that control acceptance:
  • Permitted substitutions and person responsible for approval:

09Discuss your material and part requirements

Send the component requirements and explain why a material is specified or still under consideration. OY can review the enquiry and discuss the supply and processing scope. Material availability, achievable features and inspection arrangements must be confirmed for the project.

Discuss precision CNC machining requirements →

Plan material and dimensional inspection →

Technical references

Discuss your part requirements

Send the details you have. Drawings and file uploads are optional.